Growing

How to set up a basic irrigation system for your cannabis homegrow

Published on November 26, 2019 · Last updated February 25, 2021
(f9b65183_118/iStock)

Don’t be intimidated—setting up a drip irrigation system is much simpler than it sounds. It’s basically LEGOs for adults. And it’s totally worth it: Drip systems are low-pressure, low-volume systems that deliver water exclusively where it’s needed, at the root zone of your cannabis plant.

Using a drip system minimizes evaporation, weeds (the non-cannabis kind), and problems related to moist conditions, and all the pieces will cost you less than $100. Here’s how to get the job done.

Get more tips and advice on how to ensure your marijuana crop thrives and stays hydrated from the experts at Leafly.

You’ll need:

  • Hose wye
  • Gooseneck swivel
  • Battery-powered timer
  • Vacuum breaker
  • Hose-to-thread coupling
  • Pressure regulator with filter
  • Pipe-to-thread tubing connector
  • ½-inch tubing (polyethylene)
  • ½-inch elbow connectors
  • Landscape staples
  • ¼-inch tubing (polyethylene)
  • ¼-inch barbed connectors
  • ¼-inch goof plugs
  • ¼-inch punch tool
  • ½-inch figure 8 end clamp

Step one: get your spigot ready

(Sean Walling/Leafly)
  • Add a hose wye with valves to split an outside spigot. This allows you to use one branch for the garden hose and have the other connect to your drip system.
  • A gooseneck swivel makes everything hang straight and takes stress off the plastic components.
  • A battery-powered timer will make life so easy. Don’t skip this.
  • A vacuum breaker prevents contaminated hose water from backwashing into your house’s supply lines and is often required by your state’s plumbing code.
  • A hose-to-thread coupling allows you to attach the hose to the pressure regulator and filter.
  • A pressure regulator with filter reduces incoming water pressure to a set pressure usable by a drip system.
  • Pipe-thread-to-tubing connector allows you to connect the filter to the ½-inch tubing that will go to your plants.

Step two: from spigot to planting bed

(Sean Walling/Leafly)

Use ½-inch black tubing (polyethylene)to run the line from the spigot to your planting bed or containers. It might need to be unrolled and allowed to relax first so it’s more flexible.

Hide the tubing by snaking it along walls or fences. You might also consider creating a trench for the tubing to run a few inches beneath the soil, or you may need to use ½-inch elbow connectors for any sharp turns and use landscape staples to keep it in place.

Step three: lay emitter line

Once you’ve reached your planting bed, it’s time to switch to emitters. Save yourself a whole lot of hassle by using ¼-inch tubing with pre-drilled emitters placed every 12 inches.

Use a ¼-hole punch tool to puncture the larger ½-inch tubing. Be careful not to punch through the back side! (If you do punch through or mess up, use a ¼-inch goof plug to cap it off). Use a ¼-inch barbed connector to connect to the small emitter tubing to the larger ½-inch tubing.

Snake the smaller emitter lines around the base of your plants, so the holes are positioned around the root zone on all sides of your cannabis plants. If it’s a big bed, use several shorter lines. Cap each line with a ¼-inch goof plug.

Shop highly rated dispensaries near you

Showing you dispensaries near
See all dispensaries

Step four: flush it out and cap it off

Once all the tubing and attachments are placed, turn on the water for a minute to flush dirt out of the tubing.

Afterwards, seal the ½-tubing by sliding a ½-inch figure 8 end clamp onto the open end of the tubing. Crimp a few inches of the tubing and fold it into the other side of the clamp, effectively closing it off.

Related
How to tell if a cannabis plant needs watering

How much to water?

The younger the plant, the shallower the root system, so they will require more frequent watering to prevent those little baby roots from drying out. As the season progresses, root systems grow larger and more robust, and they’ll be able to go longer between waterings.

Water when the soil is dry about ½ inch deep. You can measure this by sticking your finger in the soil down to your first knuckle. If the soil is dry, it’s time to water. The sweet spot is likely every three to five days. Err on the side of deep, infrequent waterings (after the period of establishment). Leave the drip system on long enough (fifteen-ish minutes) for water to penetrate past the root zone, encouraging roots to grow deeper.

Shop highly rated dispensaries near you

Showing you dispensaries near
See all dispensaries
Johanna Silver
Johanna Silver
Johanna Silver contributes regularly to Martha Stewart Living and Better Homes & Gardens. She's also the former Garden Editor of Sunset Magazine. She lives with her husband and young son in Berkeley, CA. In her garden she grows fruits, veggies, a little weed, and as many cut flowers as she can possibly fit.
View Johanna Silver's articles
Get good reads, local deals, and strain spotlights delivered right to your inbox.

By providing us with your email address, you agree to Leafly's Terms of Service and Privacy Policy.



Stay In Touch

Receive updates on new products, special offers, and industry news.

By providing us with your email address, you agree to Leafly's Terms of Service and Privacy Policy.

Leafly mobile app
Get high for less.
Download the Leafly app.
Download Leafly: Marijuana Reviews on the App Store
Download Leafly Marijuana Reviews on Google Play




* Statements made on this website have not been evaluated by the U.S. Food and Drug Administration. These products are not intended to diagnose, treat, cure or prevent any disease. Information provided by this website or this company is not a substitute for individual medical advice.


© 2024 Leafly, LLC
Leafly and the Leafly logo are registered trademarks of Leafly, LLC. All Rights Reserved.